表面润湿性对梯形除雾器分离性能的影响

为解决实际工业中除雾器在高气速时分离效率明显降低的问题，利用除雾器分离实验装置，以水为实验介质，采用电火花线切割技术在叶片表面构建仿生微结构实现表面疏水化，考察了表面润湿性对除雾器分离效率和压降的影响。结果表明，仿生微结构的疏水功能和减阻效应良好，表面液膜的排液速率明显加快。当气速超过5 m/s时，其液膜厚度相对较薄，可有效抑制液滴的二次夹带，提升分离效率。同时，疏水型梯形除雾器内的流场分布较平缓，流动阻力小，总压降约为带钩型梯形除雾器的一半。因此，疏水型梯形除雾器兼具高效率和低阻力特性，综合分离性能最佳。     

纳米Co/rGO磁性复合吸附材料的制备及对Cu2+的吸附性能

以改进Hummer法制备的薄片状氧化石墨烯(GO)为载体和模板负载钴离子，然后采用原位还原法制得纳米金属Co/石墨烯磁性复合吸附材料(Co/rGO)，并将其应用于对Cu2+的吸附和脱除，以期为高效可复用的铜离子脱除剂的合成与应用提供指导。实验结果证实，Co/rGO复合材料具有超顺磁性，能够很方便的使用磁铁进行分离并在无磁场情况下振荡分散。Co/rGO复合材料对Cu2+具有稳定的吸附/脱附性能，实验条件下对Cu2+的最大吸附容量达到117.5 mg/g且5 min内实现吸附平衡，远优于其原料GO的60 min吸附容量27.6 mg/g。本工作系统考察了NaOH加入量、络合剂种类、溶剂种类等关键因素对Co粒子在rGO载体上形貌和分布特性的影响，比较了不同合成条件下的复合材料对Cu2+吸附效果的影响，并对优选条件下制备的Co/rGO复合材料进行了FT-IR, XRD, SEM表征。研究结果表明，纳米Co/rGO磁性材料对Cu2+的吸附过程更符合Freundlich模型，属于多层吸附。室温下吸附焓ΔH=17.81 kJ/mol，吸附反应平衡常数Kθ=3.65。当初始Cu2+浓度为39.22 mg/L时，对Cu2+的吸附率为93.47%，五次吸附/脱附循环后吸附容量仍保持在初始值的94%，每次吸附后溶液中残余Cu2+浓度均满足钴电解液对杂质铜离子的浓度去除要求(5 mg/L)或GB 8978-1996污水综合排放标准3级(2 mg/L)，有望在相关领域发挥作用。     

基于α-FeOOH催化H2O2蒸气的低温烟气脱硝实验

针铁矿是分布广泛、储量丰富的铁氧化物，其主要成分为α-羟基氧化铁（α-FeOOH）。为了探究针铁矿在催化H₂O₂烟气脱硝反应中的性能，本文通过沉淀-水解法制备了α-FeOOH，并在自行搭建的实验台上开展了α-FeOOH催化H₂O₂的低温烟气脱硝实验研究，深入分析了H₂O₂流量、H₂O₂浓度、汽化温度、反应温度和共存气体浓度等工况参数对脱硝性能的影响。采用离子色谱（IC）分析了单独脱硝反应和同时脱硫脱硝反应后的含氧酸成分，结合各项表征分析技术考察了催化剂反应前后的理化特性和稳定性。实验结果显示，随着汽化温度和反应温度的升高，NO的脱除效率先增加后降低；增加H₂O₂浓度对脱硝效率有明显的促进作用。当汽化温度为140℃、反应温度为160℃时，以2.5mL/h注入10mol/L的H₂O₂脱硝效率达到80%。当SO₂浓度为1000μL/L时，脱硝效率提高至86.4%。离子色谱分析结果显示，单独脱硝反应和同时脱硫脱硝反应后含氧酸产物为HNO₃和H₂SO₄。反应前后催化剂的表征结果显示，α-FeOOH在脱硝反应后依然具有良好的稳定性，显示出针铁矿在低温烟气脱硝工艺中的潜在应用前景。     

安家岭储煤场输煤暗道通风除尘技术应用研究

针对输煤暗道的生产工艺现状，提出了采用通风与密闭抽尘净化技术，结合转载落料点密闭干雾降尘等技术措施，实现了输煤暗道内粉尘的的综合治理，通过粉尘浓度在线监测系统进行智能化控制，实现对输煤暗道通风除尘系统的远程连续监测监控，输煤暗道转载点下风侧5 m作业人员通行的位置总粉尘浓度由380.8 mg/m3降至19.8 mg/m3，降尘效率达94.8%，呼吸性粉尘浓度从96.7 mg/m3降至8.4 mg/m3，降尘效率达91.3%，降尘效果较好，有效地解决了输煤暗道及其转载落料点的粉尘污染问题，为输煤暗道内的粉尘防治提供参考依据。     

Physicochemical and technological properties of beef burger as influenced by the addition of pea fibre

This study aimed to evaluate the physicochemical characteristics and sensory attributes of beef burgers with the addition of pea fibre as a partial substitute of meat or fat. Three formulations were prepared: control (CON) – similar to the commercial formulation; fibre/less meat (FLM)—5% meat reduction and addition of 1% pea fibre; fibre/less fat (FLF)—7% fat reduction and addition of 1% pea fibre. Non-significant differences were obtained for pH, colour parameters (L* and b*), texture profile, cooking loss and size reduction among formulations. Moreover, sensory analysis with consumers of beef burgers did not indicate differences among the formulations for all the analysed attributes. Therefore, pea fibre is a promising partial replacer for meat and fat in beef burgers due to the preservation of technological parameters and sensory acceptance.     

CFD modeling of thermal contact resistance between solid contacting surfaces

Heat transfer has considerable applications in different industries such as designing of heat exchanger, nuclear reactor cooling, control system for spacecraft, and designing of microelectronics cooling. As the surfaces of two metals contact each other, this issue becomes so crucial. Thermal contact resistance (TCR) is one of the key physical parameters in heat transfer of mentioned surfaces. Measuring the experimental value of TCR in laboratory is highly expensive and difficult. As an alternative, numerical modeling methods could be engaged. In this study, inverse problem method solution is utilized as a proper method for estimation of TCR value. In this order, three different configurations (flat-flat, flat-cylinder, and cylinder-cylinder) were utilized in two steady and unsteady state conditions to predict the value of TCR. A comparison between the measured values and obtained values from the simulation show the errors for flat-flat, flat-cylinder, and cylinder-cylinder configuration after 10 min from starting the experiment are 4.6074%, 0.1662%, and 0.5622%, respectively. And in steady-state condition, the corresponding errors are 6.06e-3%, 1.506%, and 0.846%, respectively. In conclusion, the final results establish the fact that the inverse problem method solution can predict TCR values between contacting surfaces.     

Astragali Radix-derived nitrogen-doped porous carbon: An efficient electrocatalyst for the oxygen reduction reaction

The development of biomass-derived nitrogen-doped porous carbons (NPCs) for the oxygen reduction reaction (ORR) is important for sustainable energy systems. Herein, NPCs derived from Astragali Radix (AR) via a cost-effective strategy are reported for the first time. The as-prepared AR-950-5 catalyst shows a stacked layer-like structure and porosity. Notably, the optimized AR-950-5 delivers catalytic activity comparable to that of commercial Pt/C (C-Pt/C), with high onset potential, positive half-wave potential and large limiting current density. It also displays superior long-term stability and methanol tolerance for ORR. This work will pave the way for a new approach in the development of highly active and low-cost NPCs for fuel cells.     

超临界蒸汽参数对燃气蒸汽联合循环性能影响研究

为进一步提高联合循环效率,参考现有燃气蒸汽联合循环12.5 MPa/568℃亚临界蒸汽参数,提出27 MPa/585℃超临界蒸汽参数,根据燃气蒸汽联合循环计算模型,以397 MW燃气轮机联合循环机组为例,计算了超临界蒸汽参数与两种亚临界蒸汽参数的底循环效率和联合循环效率,并分析对比了3种蒸汽参数的底循环效率对联合循环效率的贡献。研究表明:对于同一燃气轮机,超临界和亚临界中低压蒸汽参数不同时,超临界蒸汽参数的底循环效率比亚临界提高了4.3%,蒸汽底循环输出功率占联合循环机组输出功率的百分比由30.21%增加到32.62%,联合循环净效率增加了2.21%,联合循环机组的输出功率增加了20.38 MW;中低压蒸汽参数相同时,超临界蒸汽参数的底循环效率比亚临界提高了2.87%,蒸汽底循环输出功率占联合循环机组输出功率的百分比由31.16%增加到32.62%,联合循环净效率增加了1.44%,联合循环机组的输出功率增加12.5 MW。     

Outcome‐based ventilation: A framework for assessing performance,health, and energy impacts to inform office building ventilation decisions

This article presents an outcome‐based ventilation (OBV) framework, which combines competing ventilation impacts into a monetized loss function ($/occ/h) used to inform ventilation rate decisions. The OBV framework, developed for U.S. offices, considers six outcomes of increasing ventilation: profitable outcomes realized from improvements in occupant work performance and sick leave absenteeism; health outcomes from occupant exposure to outdoor fine particles and ozone; and energy outcomes from electricity and natural gas usage. We used the literature to set low, medium, and high reference values for OBV loss function parameters, and evaluated the framework and outcome‐based ventilation rates using a simulated U.S. office stock dataset and a case study in New York City. With parameters for all outcomes set at medium values derived from literature‐based central estimates, higher ventilation rates’ profitable benefits dominated negative health and energy impacts, and the OBV framework suggested ventilation should be ≥45 L/s/occ, much higher than the baseline ~8.5 L/s/occ rate prescribed by ASHRAE 62.1. Only when combining very low parameter estimates for profitable impacts with very high ones for health and energy impacts were all outcomes on the same order. Even then, however, outcome‐based ventilation rates were often twice the baseline rate or more.